How To: Make an AC Arc Welder Using Parts from an Old Microwave, Part 2
Last time, I showed how to start putting together an AC arc welder from scavenged microwave parts, focusing on the transformer modifications. Now, I'll show you how to finish up your DIY stick welding machine by fixing up the electrical system and performing the finishing touches. Please enable JavaScript to watch this video.
Before you watch this, make sure you've seen the first video.WARNING: Stick welding, and/or the modification of a Microwave Oven Transformer (M.O.T), can be very dangerous and presents risks of UV radiation, shock hazards, burns, fires, fumes and a multitude of other risks. This project should not be attempted without a thorough understanding of electricity, adult supervision and adequate training. Misuse, or careless use, of tools or projects may result in serious injury and/or death. Use of this content is at your own risk.I started this part of the project with a scrap piece of 3/4" birch I had left over from my "Router Table" project. The measurements for the board were 7"x10", and that keeps this about as compact as practical. I found a piece of 2x2 as well, and screwed it onto the center of the board about an inch from the edge. Two pilot holes were drilled in the top to accommodate our electrode lugs.I decided to use lugs here rather than keep it all one continuous cable, because it gives the option of changing out electrode cables, or easily modifying the electrical output for future projects. Copper lugs can be pricy, but I found that if I used a 2" length of 1/2" copper tubing, I could make my own.I used a bench vise to crimp 1" of the tubing completely flat, then drilled a hole in the flat piece. A belt sander helped to clean up the edges a bit to make it easier to handle, and make it look a bit nicer as well. For the electrode cables, I used some of the 8awg cable left over from when we wound the transformer coils.Next, I exposed the copper on the end of the cable, and bent it over so it would fit inside the lower part of the lug. I flattened it with a bench vise to make a solid electrical connection, and in my testing, the connection doesn't come apart. If you don't have a bench vise, I imagine a hammer could work with very similar results.Since the system is AC, there really is no "ground" connection and it doesn't really matter which cable connects to which side, but I decided to put a "ground" clamp on the left side, and the electrode holder on the right. I also spliced the cable between the two transformers and connected them to a common lug so I could have the option to center tap the transformers for future projects, like powering an arc furnace for example.For the clamp, I found this metal one at the hardware store for only $0.99. When the rubber tips were removed, it could conduct electricity. I crimped a piece of copper tubing to the wire, then secured the tube to the clamp with a screw. For being so cheap, the clamp had a surprising amount of clamping force, which was great for biting onto the workpiece. I bought a replacement electrode holder for $13 rather than making my own. It looked better and was much more practical for welding with.I used one of the cords saved from one of the microwaves and cut off the green wire, and secured the cable to the wood base to prevent the cables from pulling off the connections. The black cable connects to one of the primary terminals on one of the transformers, and the white wire connects to one of the other transformers primaries. It doesn't really matter which one. I used another piece of wire to connect the other 2 posts together, essentially connecting the 2 transformers in series.Later on, when the device is tested, the two electrodes should be outputting around 36 volts. If you're seeing very low voltage, like 2.4 in my case, that means the transformers are canceling each other out, and this can be fixed by just switching the connections on one of the transformers. I went ahead and did that and ended up with about 37 volts between my ground clip and electrode holder.I needed 240 volts AC to power this system, so I used 2 plugs, a connector, and some 10awg wire. Each of the outlets in my house output around 120 VAC, and the circuits all connect back to the breaker bus bars. There are 2 busses, and I learned that if I took a hot line from each bus, the electrical potential between them was 240 VAC.Rather than tapping into the breaker box directly, I used extension cords and connected to 2 different outlets that were 180 out of phase (on separate bus bars). When they were connected to my adapter, the result was 240 VAC.It's important to keep in mind that this welder doesn't have an on/off switch, and no current limiting of it's own. That's why I had to build a separate power controller I call the "Scariac". It's like a "Variac" except much more dangerous. But it is pretty cheap, and it gets the job done. Look for how to build the Scariac in a different project.To set the current for welding 1/16th rods, I connected the ground clamp and electrode holder together, effectively shorting out the system. The Scariac has a loop of wire built in that allows me to monitor the primary current, and when it's set to about 15.5 amps on the primary, it gives me around 100 amps on the secondary. Cranking up the power on the Scariac can get the welding cables up over 200 amps, but I really don't recommend running them that high for more than a few seconds or the plastic coating on the cables will overheat and may start melting. In any case, you can see there is certainly enough power for welding.I burned ten 1/16 rods in a row, and the system was only warm to the touch. This gives me the impression it's got a pretty good duty cycle for use with the smaller rods, and these are probably the only one's I'll really need for my hobby use anyway.Rather than leaving all the terminals exposed, I picked up a plastic container, painted it black, and drilled a few holes for the cables. I used the top as the base, and the bottom as the top. It seemed to work pretty well.There are also ventilation holes cut in the sides to allow airflow over the coils, and even consideration made for attaching a fan to blow cool air and help regulate the temperature while welding. At this point, the system is completely finished and ready for welding!You can see some of my first few experiences with the world of welding in the video below. Please enable JavaScript to watch this video.
Well, there you have it! A homemade AC stick welder. If you haven't see the video yet, it's not too late. Watch it here!If you like this project perhaps you'll like some of my others. Check them out at thekingofrandom.com.
You can upload videos to YouTube in a few easy steps. Use the instructions below to upload your videos from a computer or from a mobile device. Upload videos
Youtube degrades my HD Video? | Tom's Guide Forum
Note: Deleting apps on your Apple Watch will not delete their companion app on your iPhone. How to Remove Applications Using Your iPhone. Using the Watch itself to delete an app is a no-brainer, but your phone may be easier to use or closer to you in some cases.
How to Delete or Uninstall Apple Watch app using iPhone
How to make your Android phone look like a Windows phone
All account details, i.e., the account name, the name of a character as well as the password can be regained through the account recovery process.. Account recovery can be started by clicking on the "Forgot Password?" link on the account management login page, or by opening the account recovery page directly.
If you forgot your Apple ID password - Apple Support
Forza le app come Netflix per mostrare il salvaschermo sul tuo Nexus Player Per qualche strana ragione, l'app Netflix ama disabilitare lo screensaver integrato del Nexus Player. Non usa il proprio, semplicemente mantiene il tuo schermo a tempo indeterminato, il che ovviamente può portare a burn-in dello schermo.
How to Sideload Apps on the Nexus Player « Cord Cutters
How to Organize Tasks Better & Increase Your Overall
Use Google Drive files offline - Computer - Google Drive Help
However, it only lets you view YouTube videos, which is a drawback when there are so many good video hosting sites out there. If you want floating windows for YouTube videos as well as Facebook, TED, Vimeo, Vine, and other media sites, there's a better option. The only downside is that it requires root access.
Android 8.0 'Octopus' Could Be a Complete Misdirect
Here are a few tips to help you improve sound quality and increase volume on Android. You can try a speaker booster or volume booster app, but plenty can be improved with a little audio know-how
The Easiest Way to Increase Audio Quality on Any Android
Developers Aravind Sagar and Priyan Vaithilingam have ported this functionality to devices running KitKat, so you don't have to wait to try out Lollipop's Smart Lock features. In addition, their app replicates the look and functionality of 5.0's all-new lock screen, so it's definitely worth a look.
Get Android Lollipop's New "Smart Lock" Feature on KitKat
One of the more annoying things about the Google Voice service, since it's release, has been the inability to use an existing phone number with the service. At sign-up (if you were lucky enough
How to Install and use Google Voice on your Android phone
Looking for awesome Google Chrome or Android Easter eggs? In this video tutorial I show you how to find and play a hidden game in Google Chrome. This works on both the chrome desktop browser as
How to play the dinosaur mini-game in Google Chrome - YouTube
How to remove a widget from your iPhone, iPad's Lock or Home screen To remove a certain widget from your iPhone or iPad's Lock or Home screen you will follow the same process as you did to add
Use widgets on your iPhone, iPad, and iPod touch - Apple Support
How to Move Pictures from Android to SD Card. This wikiHow teaches you how to transfer pictures from your Android's internal hard drive onto an SD card. You can do this using your Android's built in settings, or you can use a free app
How Do I Get Pictures Off an SD Card Onto My Computer
0 comments:
Post a Comment